How to Replace a Kia Sportage Replacement Key

For a number of Kia models the key comes with the keyless entry system that is built into the key. This key is similar to a remote control, and can be exchanged with a Kia dealer.

Key fobs might stop working due to a number of reasons, including batteries that are dead, worn-out buttons, signal interference or water damage. Here are some guidelines on how to get your kia picanto key replacement Sportage replacement key to function again.

How to replace a remote key or a smartkey?

No matter if your Kia comes with an intelligent key, remote key push to start key, or a regular non-transponder metal key the battery in these keys will eventually need replacing. This is especially true if your car displays a message telling you that the remote or smart keys are in poor condition.

It's a fairly simple process. To replace the battery of the keyfob remove your mechanical key from the slit at the back of the fob. Then, pull the cover off. Inside the key fob will be a small screw that holds the battery in the correct position. With a small screwdriver, loosen the screw and pull out the battery that was in place. Insert the new battery and then close the cut on the key fob.

Test the key fob by pressing the lock/unlock buttons. You're good to go in case the doors lock and unlock as you expect. You can now use the kia car Key replacement's hands-free lock/unlock feature when your fingers are cold or you have to run some errands in Brandon.

Note: Some key fobs (transponder chip or smart keys) may need to have their programming completed. This requires a special programming machine that only the dealer or locksmith has access to. Other keys (non transponder metal keys), do not need programming. If your key has to be programmed, you must be aware of the key code written on the tag of the key code and record the number in a secure place.

How do I replace a battery

If the Kia key fob doesn't respond to pressing the lock or unlock button, it is likely that the battery is depleted. A low battery may cause other issues, like the check engine light flashing or the engine not turning correctly. Fortunately replacing the key fob battery is a relatively easy DIY project that requires only the most basic tools.

Before you begin the process, make sure that your vehicle is off and all doors are closed. Find the small metal or a plastic piece at the bottom of the key fob. Move it until the metal key pops out. The key can be inserted into the driver door handle to unlock your car.

To replace the battery on the key fob, take off the cover at the rear. Use a plastic pry tool to loosen the latch that holds the black negative cable. Remove the old battery and then orient the new one so that the "+" positive side faces you and the "negative" negative side is facing the fob's metallic electrical contacts. Avoid using excessive force when pushing the new CR2032 into place to avoid damaging or breaking the metal contacts.

After installing the new battery, turn the key fob off and on in the ignition until the door locks cycle. You can then test your kia key replacement key fob to determine whether it's functioning properly again.

How do you replace a smart keys

There is a possibility of having a standard keyfob or a Smart Key, based on the model of Kia Sportage. The difference between them is that the smart key has tiny mechanical key blade tucked inside it, while the standard fob does not. Both types of key fobs are equipped with batteries inside which eventually needs to be replaced. Luckily, this is quite simple and only takes about two minutes.

Make sure you turn off your Kia and sit on a level or well-lit surface prior to when you begin. Be aware that the fob is made up of small pieces that could be thrown off should you not be careful.

The first step is to find the small release button on the backside of the fob. It could be a circular or rectangular slot. You can open the key fob by pressing the button.

Once you have the key fob open and you are able to take out the old battery and replace it. The new battery is a CR-2032 that can be purchased online or at a local auto parts store. After you've finished you should be able to lock, unlock and start your vehicle with your key fob even if your engine isn't running!

How do you replace a broken mechanical key

The Kia keyfob can be a fantastic convenience that allows us to lock or unlock our car by pressing a button. Like any other device, the Kia key fob can occasionally have problems. Luckily, there are steps that can be taken to troubleshoot these issues and ensure that our key fobs are in good working condition in the long run.

A dead or drained battery is among the most common problems. This can cause the device to stop working entirely or even to stop working intermittently. If this is what you are experiencing you should replace the battery an entirely new battery.

If this does not resolve the issue, use a flathead screwdriver standard to wedge the fob's plastic casing open. Be sure not to damage any internal components or scratch the plastic. After the battery has been removed, replace it with a brand new one.

Close and open the door with the mechanical key. (Every kia fob comes with an emergency mechanical key which will fit into the slot). Test the fob to make sure it's working properly. If the fob not working, contact a dealer or locksmith to resolve the issue. To avoid locking outs in the future, ensure that you have an emergency key that can work in all of the door and trunk cylinders.